Leading 10 usual forklift accidents ， forklift operation need to pay attention to these issues ！.

Don't take too lightly the forklift at work. If the operation is not good, there will be major mishaps in mins, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead could not be found, causing a moving accident.
Instance 2: In order to preserve the balance of the forklift when raising heavy products, the workers utilized their body weight as the weight, which almost created casualties.
Situation 3: The size of the forklift cargo exceeds the allowed size of the path and hangs on the roadside shelf, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the safety belt, the forklift lifter drops and the vehicle driver is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning must be sluggish and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no barriers overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to lose side security and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it must obey the web traffic rules in the factory and need to maintain a specific safety distance from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be elevated other than when piling or packing. .
8. The elevation of the tons should not block the chauffeur's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing duty. .
12. If issues are found, they will be fixed and reported in a timely fashion, and they will certainly never operate with diseases or hide them.

packing and discharging.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing ought to be against the shelf. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the car need to be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it needs to be noted that the fork pointer should not touch various other items or objects. The tons should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be tilted ahead a little when the lots is lowered to enable very easy positioning of the load and extraction of the forks. .
6. It is restricted to fork items at high speed and hit difficult things with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding stay Stand-on Electric Pallet Stacker clear of the collapse of the goods and hurt people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay Electric Forklift Truck for Warehouse clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubing oil and air conditioning water must be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak must likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the slope is above 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for long distance driving.
3. It is not enabled to pick up the goods by turning over the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844